Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Lyuks Lak-R Gloss — transparent lightfast floor varnish
ELAKOR

Elakor-PU Lyuks Lak-R Gloss — transparent lightfast floor varnish

Sealers and topcoats

This two-component varnish is applied as a topcoat over polyurethane and epoxy coatings to increase their chemical and wear resistance; it is also used to seal decorative floors with flakes, chips and glitter and to coat parquet. Porous substrates — concrete and wood — must be primed before varnishing until the pores are closed. The varnish is applied in two coats with a velour roller at +5…+20 °C; film tensile strength is at least 40 MPa, Taber abrasion 5 mg, fire hazard class KM1.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typevarnishes and topcoats
Useproduction workshops, warehouses and logistics, car parks and ramps, retail and public premises, outdoor areas, chemically resistant, decorative
Basetwo-component polyurethane varnish, lightfast
Colourtransparent, colourless; gloss
Packaging“A” + “B” = kit 16 kg + 2 kg = 18 kg
Application methodTopcoat over polyurethane and epoxy coatings to increase chemical resistance and wear resistance; sealing of decorative coatings with flakes, chips, glitter; transparent impregnations for concrete, stone, brick, tile; coatings for parquet. Transparent topcoat over polyurethane and epoxy coatings; do not apply to concrete, wood and other porous surfaces without prior priming until the pores are closed. “Velour-Wool” roller (5 mm nap), brushes at abutments; 2 coats, rolling in two mutually perpendicular directions, strictly observe the consumption rate. Relative air humidity not more than 80%; surface 3°C above the dew point; surface temperature difference not more than 3°C during application and for a day afterwards; on the lowest floor – waterproofing against groundwater.
Application temperaturesurface, air, materials: +5°C…+20°C
Curingdrying to degree 3 at +20°C not more than 10 h; drying of the 1st coat 6-12 hours, but not more than 24 hours; after application at +15…20°C: foot traffic – 3 days, full mechanical load – 7 days, full chemical load – 14 days
Key propertiesA:B ratio 8:1; mix viscosity VZ-4 10-12 s; solids content at least 32%; density 0.92 kg/l; service temperature range from -60°C to +100°C (up to 30 min – up to +150°C); water absorption not more than 0.1%; film tensile strength at least 40 MPa; elongation at least 8%; impact strength at least 100 cm; Shore D at 28 days 70-74; flexibility not more than 1 mm; Taber abrasion CS-10, 1 kg – 5 mg; fire hazard class KM1; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumption2 coats; consumption per coat: to change surface gloss 60-70 g/m², to seal chips, flakes, glitter 70-80 g/m²
Shelf life8 months in the manufacturer's original packaging; store and transport at temperatures from -30°C to +25°C
StandardsCertificate of conformity (fire safety); Certificate of conformity; Approval for use in children's and healthcare institutions

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR