Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
UTECH HITRE 500 chemical bonded anchor — epoxy anchor for rebar and studs
UTECH

UTECH HITRE 500 chemical bonded anchor — epoxy anchor for rebar and studs

Chemical anchors

UTECH HITRE 500 is a two-component epoxy bonded anchor for setting M8–M36 threaded studs and rebar of 8–40 mm diameter in cracked and non-cracked B25–B60 concrete, aerated concrete and natural stone. Holes may be dry, water-saturated or water-filled, and installation is carried out in floors, walls and ceilings at substrate temperatures from −10 to +40 °C. The anchor has been tested for seismic loads and radiation resistance, holds a technical certificate of the Ministry of Construction of Russia and is included in the register of Russian industrial products of Minpromtorg (GISP).

Specifications

ManufacturerUTECH — OOO “ASP-GRUPP”, Ivanteyevka
Typechemical anchors
Useanchoring of rebar and bolts, bridges and overpasses, columns and beams
Basetwo-component epoxy-based adhesive compound (component A — epoxy resin, 1,4-butanediol diglycidyl ether, 3-glycidoxypropyltrimethoxysilane; component B — 1,5-diamino-2-methylpentane)
Packagingtube 585 ml; two-component dispensers HDM 500 / HDE 500 with cartridge U-500
Application methodbonding of threaded studs M8–M36 (embedment depth hef from 50–160 mm for M8 to 144–720 mm for M36) and rebar Ø8–40 mm; concrete B25–B60, cracked and non-cracked, aerated concrete not below B3.5, natural stone; dry, water-saturated and water-filled holes; installation in floors, walls and ceilings; extension and strengthening of reinforced concrete structures, post-installed rebar starters, fixing of steel columns, beams and base plates; hole by hammer drilling (for HITRE 500 also by diamond drilling, with roughening), cleaning with a brush and blowing out; discard the first compound from a new mixer; fill the hole to about 2/3 from the bottom, insert the stud or rebar with a twisting motion; apply load after full strength gain; a started tube with the mixer screwed on can be used within 7 days (new mixer, discard the first compound again)
Application temperaturesubstrate from −10 to +40 °C; tube temperature during installation not below +5 °C
Curingworking time / full strength gain by substrate temperature: +35…+40 °C — 12 min / 4.5 h; +30…+34 °C — 15 min / 5 h; +25…+29 °C — 20 min / 6 h; +20…+24 °C — 30 min / 7 h; +15…+19 °C — 1 h / 12 h; +10…+14 °C — 1.5 h / 16 h; +5…+9 °C — 2 h / 24 h; 0…+4 °C — 2 h / 48 h; −5…−1 °C — 2 h / 168 h; −10…−6 °C — 6 h / 240 h; in a damp substrate (from +5 °C) the strength-gain time doubles
Key propertiescharacteristic bond strength of the adhesive to B25 concrete (hammer drilling, floors and walls, dry and water-saturated substrate), temperature range I: non-cracked τn,urc 17.8 / 17.9 / 18.3 / 17.0 / 15.8 / 14.3 / 13.3 / 12.1 / 10.6 N/mm² (M8 / M10 / M12 / M16 / M20 / M24 / M27 / M30 / M36), cracked τn,rc 7.8 / 7.8 / 8.0 / 7.4 / 6.9 / 6.4 / 6.0 / 5.8 / 5.3 N/mm²; water-filled hole, non-cracked — 14.7…8.1 N/mm²; temperature range II: non-cracked 10.1…6.0 N/mm², cracked 4.4…3.0 N/mm²; characteristic pull-out loads in non-cracked B25 concrete 10.7–628.0 kN, cracked 3.0–452.2 kN (per the technical certificate, depending on diameter and embedment depth); temperature range I −60…+42 °C (long-term up to +25 °C), range II −60…+70 °C (long-term up to +42 °C); tested for seismic loads (seismic categories K1/K2 per STO 02066523-001-2020) and for radiation resistance
Shelf life12 months from the date of manufacture; storage at +5…+25 °C in closed packaging, in dry heated premises, no closer than 1 m to heating appliances, do not freeze
StandardsSTO 17523759-031-2025; certificate of conformity SDS “SMIK” No. RU.SMIK.001.N.00561 valid from 27.03.2026 to 26.03.2029; technical certificate of the Ministry of Construction of Russia No. 7425-26 dated 27.03.2026 (valid until 27.03.2028, HITRE 500 and ICE 500); SGR RU.42.21.04.008.E.000086.05.26 dated 28.05.2026; register of Russian industrial products of Minpromtorg (GISP); design per SP 513.1325800.2022, SP 63.13330.2018, STO 02066523-001-2020 (seismic); post-installed rebar starters — GOST R 58429-2019, GOST R 58387-2019; included in the STO of SC “Avtodor”

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by UTECH