BIRSS
BIRSS Leytlak — conductive layer of an antistatic floor
Water-emulsifiable epoxy conductive sealer — the intermediate electrically conductive layer of the BIRSS Leytpol antistatic floor system.
Price on request
BIRSS
BIRSS Ultrapol 100 — highly filled epoxy floor
Ultrapol 100 is an unpigmented epoxy binder that works together with the graded quartz sands “BIRSS Napolnitel Ultrapol” (Ultrapol filler), so the colour of the coating is set by the filler itself. The result is a dense floor for chemical and food production, garages, car washes, covered car parks and warehouses, including non-slip and watertight versions. Compressive strength is 100 MPa, flexural strength more than 35 MPa, service temperature up to +110 °C.
Specifications
| Manufacturer | BIRSS — AO “Opytny Zavod Sukhikh Smesey”, Moscow |
|---|---|
| Type | epoxy floors |
| Use | production halls, chemically resistant, food and pharmaceutical, car parks and ramps, warehouses and logistics |
| Base | two-component unpigmented solvent-free epoxy compound; used in a system with the graded quartz sands “BIRSS Napolnitel Ultrapol” |
| Colour | rich colour of the quartz filler |
| Packaging | metal pails, kits (A+B) of 25 kg |
| Application method | primer — Ultrapol 100 without filler, with a quartz broadcast; main layer with filler by squeegee (up to 5 mm) or compacted with a roller/power trowel (“helicopter”) (from 8 mm); broadcast of graded or wear-resistant filler |
| Application temperature | not below +15 °C; substrate +15…+30 °C (3 °C above the dew point) |
| Curing | drying to degree 3 — 8–12 h; further work after 24 h; foot traffic after 3 days; full cure after 7 days |
| Key properties | compressive strength 100 MPa, flexural >35 MPa (per the description); Shore hardness 80; bond to concrete at least 2.5 MPa (failure in the concrete); service temperature −30…+110 °C (wet exposure up to +95 °C short-term, +65 °C long-term); chemical resistance: acids 10 %, alkalis 50 %; resistant to most chemicals (acid solutions, alkalis, oils, solvents) |
| Layer thickness | from 5 to 100 mm (highly filled coatings); examples — up to 5 mm and from 8 mm |
| Consumption | self-levelling up to 5 mm: primer Ultrapol 100 0.2–0.4 + quartz 1.2 kg/m²; main layer Ultrapol 100 0.5 kg/m²/mm + Napolnitel Ultrapol 1.25 kg/m²/mm; broadcast 4–5 kg/m² (or wear-resistant filler 5–6 kg/m²); watertight from 8 mm: Ultrapol 100 0.26 kg/m²/mm + filler 1.94 kg/m²/mm |
| Shelf life | not more than 12 months in closed original packaging; protect from sunlight, heat and freezing |
| Standards | TU 2257-018-05668056-01 with amendments No. 1, No. 2 |
Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.
Other materials by BIRSS
BIRSS
BIRSS 59 S2 M700 Moroz — 70 MPa R4 mix placed from −15 to +30 °C
Thixotropic mortar with microfibre for repairing bridges, tunnels and port structures from −15 to +30 °C; at +20 °C it reaches 70 MPa in 28 days.
Price on request
BIRSS
BIRSS 67 Shpurovaya — non-shrink injection compound for anchors and cracks
Flowable cementitious compound for crack injection, anchor fixing, grouting of bearings and soil stabilisation; water retention at least 98 %.
Price on request
BIRSS
BIRSS RSM-2M M550 Moroz — R4 repair mix with anti-freeze admixture
Mix for hand repair of joints, cracks and concrete defects without formwork at low and sub-zero temperatures; at +20 °C it reaches 55 MPa in 28 days.
Price on request
BIRSS
BIRSS UK-2 hardener — corundum topping for industrial floors
Corundum hardening mix for heavy-duty concrete floors: compressive strength at least 65.0 MPa, abrasion 0.4 g/cm².
Price on request
BIRSS
BIRSS Izipol — elastic polyurethane self-levelling floor
Solvent-free polyurethane floor for mechanical and impact loads in industry, car parks, warehouses and retail.
Price on request