Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PTs T3 — textured polyurethane-cement floor for heavy loads
ELAKOR

Elakor-PTs T3 — textured polyurethane-cement floor for heavy loads

Polyurethane-cement floors

This textured polyurethane-cement floor is designed for significant and very significant intensity of mechanical exposure — high abrasive, impact and vibration loads — as well as thermal and chemical exposure. The compound is spread with a gauge rake, smoothed with a narrow steel trowel within 15 minutes and rolled with a spiked roller. Service temperature is from −40 to +80 °C continuously and up to 150 °C short-term, compressive strength 52 MPa, Shore D hardness 80–85.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane-cement floors
Useproduction workshops, warehouses and logistics, car parks and ramps, food and pharmaceutical, chemically resistant
Basepolyurethane-cement three-component compound for textured coatings
Colourgrey, light grey, beige, brown, yellow, blue, green, black; semi-matt/matt finish (the shade may change over time)
PackagingComp. “A” 2.1 kg + Comp. “B” 1.9 kg + Comp. “C” 22 kg = Kit 26 kg
Application methodSubstrate: monolithic concrete, concrete and sand-concrete screeds, grade strength not lower than M350 (B25), new concrete cured for at least 28 days; surface moisture is not limited (there must be no puddles); relative air humidity and dew point are not limited. Preparation: grinding with a terrazzo grinding machine (“000”/“00” segments) or shot blasting; primer Elakor-PTs Grunt (drying at least 24 h at +20°C). Mix only a full kit. Scarify to not more than 2 mm with a milling machine; anchor grooves 6-10 mm. Spread with a gauge rake with adjustable gap, smooth with a narrow steel trowel within not more than 15 minutes, then roll with a spiked roller.
Application temperatureair, surface: optimum +17…+23°C; permissible +10…+30°C; material temperature +18…+22°C
Curingpot life on the surface at (20±2)°C at least 15 min; at (20±2)°C, relative air humidity 70%: foot traffic – 24 h, full mechanical load – 7 days, full chemical load – 14 days
Key propertiesA:B:C ratio by weight 2.1 : 1.9 : 22.0; density 2.1±0.02 kg/l; adhesion (GOST 28574-2014) to concrete B25 > 2.5 MPa, to concrete B40 > 4.0 MPa (failure in concrete); compressive strength (28 days) 52 MPa; flexural 16 MPa; tensile 8 MPa; Shore D hardness 80-85; impact strength U-2M 100 cm; service temperature -40°C…+80°C continuous, short-term for up to 2 h up to 150°C; fire hazard class KM2 (V2, D1, T1, RP1); chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Layer thickness8-12 mm
Consumptiontheoretical consumption 2.1 kg per 1 m² per 1 mm of layer; allowing for filling of grooves and a 5% technological reserve – 2.2 kg
Shelf lifecomponents “A” and “B” – 12 months, component “C” – 6 months in the manufacturer's original packaging; store and transport at temperatures from +5° to +25°C
StandardsCertificate of conformity (fire safety) “Elakor-PTs”, class KM2; Certificate of conformity “Elakor-PTs”

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR