Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Lyuks Emal Elastic Lightfast — elastic polyurethane paint
ELAKOR

Elakor-PU Lyuks Emal Elastic Lightfast — elastic polyurethane paint

Polyurethane floors

A Shore D hardness of only 30–35 and elongation of at least 60 % allow this enamel to work on “soft” and deformable substrates — rubber crumb coatings, rubber mats, elastic polymers — as well as on concrete, wood and metal. It is used for elastic coloured and decorative coatings, protective topcoats and line marking on sports and rubber floors. Lightfastness is 7 (“excellent”), gloss 80–95 %; according to the technical data sheet, the enamel is used in sports halls, at stadiums and outdoor sports grounds, in medical institutions and premises with vibration loads.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane floors
Useproduction workshops, warehouses and logistics, car parks and ramps, retail and public premises, food and pharmaceutical, wet rooms, outdoor areas, chemically resistant, decorative
Basetwo-component polyurethane weather-resistant elastic paint; acrylic-urethane prepolymers, organic solvents, pigments, functional additives
Colourcoloured; gloss finish (60° 80-95%)
PackagingComp. “A” 15.0 kg + Comp. “B” 5.0 kg = Kit 20.0 kg
Application methodElastic coloured paint-on coatings of specified hardness; UV-protective topcoats on “soft” and deformable substrates; elastic decorative coatings with chips, flakes; line marking on elastic and rubber coatings. Substrates: concrete, sand concrete, rubber crumb coatings, rubber mats, elastic polymers, wood, metal, polymers. Brushes or rollers (12-14 mm nap), airless (without thinner) or air spraying (5-10% xylene or solvent); 2 coats. Relative air humidity not more than 80%; surface moisture not more than 4 wt%; 3°C above the dew point.
Application temperatureair and surface: from +5°C to +25°C; material: from +5°C to +25°C
Curingpot life at +20°C at least 60 min; drying to degree 3 at +20°C, relative air humidity 65% not more than 8 h; after application at +15…20°C: foot traffic – 3 days, full mechanical load – 7 days, full chemical load – 14 days
Key propertiesmix viscosity VZ-4 30-50 s; solids content at least 72%; density 1.10-1.15 kg/l; service temperatures at relative air humidity up to 80% from -60°C to +100°C, at relative air humidity above 80% from -40°C to +80°C; water absorption not more than 0.1%; film tensile strength at least 16 MPa; elongation at least 60%; impact strength 100 cm; Shore D at 28 days 30-35; flexibility not more than 1 mm; gloss at 60° 80-95%; lightfastness 7 (excellent) per ISO 9370-2017; Taber abrasion CS-10, 1000 g, 28 days – 24 mg; fire hazard class KM1; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumption2 coats, 150-200 g/m² per coat
Shelf life8 months in the manufacturer's original packaging; store and transport at temperatures from -30°C to +25°C

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR