Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Lyuks Antistatic Paint SK PROF (AST-7, AST-6) — nanotube paint
ELAKOR

Elakor-PU Lyuks Antistatic Paint SK PROF (AST-7, AST-6) — nanotube paint

Polyurethane floors

The electrical conductivity of this paint is created by single-walled carbon nanotubes, and the polyurethane base itself is weather-resistant and lightfast: lightfastness per ISO 9370-2017 is 7 (“excellent”). The paint is applied in 1–3 coats by roller, brush or spraying onto any building substrates prepared with “Elakor” materials, including over anti-corrosion and fire-retardant coatings; conductive versions are made with copper strips. The “surface – ground” resistance is not more than 10⁷ Ω for AST-7 and not more than 10⁶ Ω for AST-6; a coat dries to degree 3 in not more than 1 hour.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane floors
Usewarehouses and logistics, production workshops, food and pharmaceutical, outdoor areas, chemically resistant, antistatic/conductive
Basecoloured electrically conductive two-component polyurethane compound, lightfast
Colourcoloured; gloss at 60° 90-98%
Packaging“A” + “B” = kit 15 kg + 3 kg = 18 kg
Application methodPaint-on antistatic coatings for floors, walls, ceilings, structures; renovation of existing antistatic coatings; over anti-corrosion and fire-retardant coatings; conductive versions – with copper strips. Substrates – any building materials prepared with “Elakor” materials. Mixing in the container of comp. “A”, standing time 20-25 min. Rollers (12-14 mm nap), brushes; airless spraying (without thinner); air spraying (up to 5% xylene or solvent); 1-3 coats. Relative air humidity not more than 80%; surface moisture not more than 4 wt%; 3°C above the dew point.
Application temperatureair and surface: from +5°C to +25°C; material: from +15°C to +22°C
Curingpot life of the mix at +20°C 40 min (use within 40 minutes after standing); drying to degree 3 at +20°C, relative air humidity 65% not more than 1 h (forced drying up to +80°C – not more than 10 min); drying between coats at +15…20°C – 8-12 h, but not more than 24 h; after application at +15…25°C: foot traffic – 3 days, full mechanical load – 7 days, full chemical load – 14 days
Key propertiesA:B ratio – stated on the label of comp. “A”; mix viscosity VZ-4 20-25 s; solids content at least 54%; density 1.07 ± 0.01 kg/l; service temperatures at relative air humidity up to 80% from -60°C to +100°C, at relative air humidity above 80% from -40°C to +80°C; water absorption not more than 0.1%; Rs AST-7, AST-6 not more than 10^9 Ω (GOST IEC 61340-4-1-2017, GOST 6433.2-71); Rg “surface-to-ground”: AST-7 at Vtest=100 V not more than 10^7 Ω, AST-6 at Vtest=10 V not more than 10^6 Ω; film tensile strength at least 27 MPa; elongation at least 20%; impact (U-2M) direct 100 cm, reverse 50 cm; Shore D at 28 days 70-75; flexibility not more than 2 mm; lightfastness 7 (excellent) per ISO 9370-2017; Taber abrasion CS-10, 1000 g, 28 days – 22 mg; chemical resistance: high chemical resistance
Consumption1-3 coats, 120-150 g/m² per coat
Shelf life6 months in the manufacturer's original packaging; store and transport at temperatures from 5°C to 25°C

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR