VMP
VINIKOR BEP-5297 — epoxy enamel for containers with drinking water and food products
Epoxy enamel for tanks, silos and containers: permits contact with drinking water and food products at temperatures up to +60 °C.
Price on request
VMP
IZOLEP-epolain — epoxy urethane coating for metal and concrete
The two-pack epoxy urethane composition with high solids — 90 % by volume — forms a gloss coating resistant to mechanical wear and abrasion. It protects metal, reinforced concrete and other mineral surfaces against gases, aqueous salt solutions and short-term splashing with acids, alkalis, crude oil and petroleum products. It is designed for an industrial atmosphere without ultraviolet radiation and is therefore not used on surfaces in direct sunlight; concrete is cured for at least 28 days before painting, and the coating dries for at least 7 days before service in aggressive conditions.
Specifications
| Manufacturer | VMP — AO “NPKh VMP”, Yekaterinburg |
|---|---|
| Type | epoxy enamels and coatings |
| Use | steel structures, concrete |
| Base | epoxy urethane composition, two-pack (base and hardener); high solids |
| Colour | white, grey, red-brown, black, other colours by agreement with the customer; gloss |
| Packaging | kit: base in metal pails, hardener in metal cans (depending on the kit weight) |
| Application method | airless spray (nozzle 0.015–0.021″, 15–22 MPa) and air spray — 1–2 coats; brush, roller — 2–3 coats; thinner SOLVIN-15: 5–10 % (airless), up to 10 % (air spray, brush, roller) by weight |
| Application temperature | from +5 to +35 °C, relative humidity max. 80 %; surface at least 3 °C above the dew point |
| Drying | to degree 3 — no more than 18 h at 20 °C; drying between coats at +20 °C — at least 16 h; before service in aggressive conditions — at least 7 days at 20 °C; pot life at least 40 min at 20 °C |
| Key properties | volume solids — 90±2 %, non-volatile matter by weight — at least 95 %, density — 1.6–1.9 g/cm³, resistance to gases, aqueous salt solutions, short-term splashing with acids, alkalis, crude oil and petroleum products, mechanical wear and abrasion, service in an industrial atmosphere without UV radiation |
| Shelf life | 12 months |
| Standards | TU 20.30.12-018-67503963-2019; state registration certificate No. RU.77.01.34.008.E.003241.12.21 of 20.12.2021 |
Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.
Other materials by VMP
VMP
VINIKOR primer-enamel — vinyl-epoxy, for steel, galvanised steel and aluminium
Vinyl-epoxy primer-enamel for steel structures, bridges and ships; low flame spread, applied down to −10 °C.
Price on request
VMP
VM-8352N — epoxy powder for the second layer of factory pipe coating
Powder material for pipe plants, sprayed as a second layer over uncured VM-6233R onto a heated pipe.
Price on request
VMP
IZOLEP-oil 250 — epoxy coating for storage tanks and fuel tanks
Epoxy coating for containers with crude oil, diesel fuel and oils in 1–2 coats; applied and cured from 0 °C.
Price on request
VMP
ALUMOTAN — polyurethane enamel with aluminium powder
Silver moisture-curing finish over TSINOTAN, TSINEP and TSVES zinc primers for bridges, oil and gas and power, heat resistance 150 °C.
Price on request
VMP
FERROTAN — polyurethane enamel with micaceous iron oxide
Moisture-curing enamel with micaceous iron oxide — an intermediate coat over zinc primers for bridges, oil and gas, chemical plants and hydraulic structures.
Price on request