UTECH
UTECH SP-EG epoxy grout — non-shrink grout under equipment
Non-shrink epoxy grout under columns, equipment and bridge structures under static and dynamic loads; 100 MPa in 7 days.
Price on request
UTECH
UTECH HITRE 100 chemical bonded anchor — epoxy anchor for everyday installation
The epoxy anchor UTECH HITRE 100 is intended for everyday fixings — temporary structures, fences, railings, gates, grilles, wall-mounted equipment, air conditioning and lighting systems. It bonds M8–M24 threaded studs and rebar of 8–25 mm diameter into dry hammer-drilled holes in B25–B60 concrete, including cracked concrete, in compression and tension zones. Installation is carried out at substrate temperatures of +5…+40 °C, the connection works from −40 to +42 °C; the 585 ml tube is white or black.
Specifications
| Manufacturer | UTECH — OOO “ASP-GRUPP”, Ivanteyevka |
|---|---|
| Type | chemical anchors |
| Use | anchoring of rebar and bolts |
| Base | two-component epoxy-based adhesive compound (component A — epoxy resin, 1,4-butanediol diglycidyl ether, 3-glycidoxypropyltrimethoxysilane; component B — 1,5-diamino-2-methylpentane, m-xylylenediamine, 3-aminopropyltriethoxysilane, quartz flour) |
| Colour | white or black tube |
| Packaging | tube 585 ml; two-component dispensers HDM / HDE with cartridge U-500 |
| Application method | bonding of threaded studs M8–M24 (hef from 60–160 mm for M8 to 96–480 mm for M24) and rebar Ø8–25 mm in a dry substrate of B25–B60 concrete, cracked and non-cracked, hammer-drilled holes; compression and tension zones of concrete; everyday fixings: temporary structures, fences, railings, gates, grilles, wall-mounted equipment, air conditioning and lighting; hole by hammer drilling (for HITRE 500 also by diamond drilling, with roughening), cleaning with a brush and blowing out; discard the first compound from a new mixer; fill the hole to about 2/3 from the bottom, insert the stud or rebar with a twisting motion; apply load after full strength gain; a started tube with the mixer screwed on can be used within 7 days (new mixer, discard the first compound again) |
| Application temperature | substrate +5…+40 °C; tube temperature during installation +5…+35 °C |
| Curing | working time / full strength gain: +5…+9 °C — 2.5 h / 24 h; +10…+14 °C — 2 h / 16 h; +15…+19 °C — 1.5 h / 12 h; +20…+24 °C — 1 h / 7 h; +25…+29 °C — 45 min / 6 h; +30…+34 °C — 30 min / 5 h; +35…+40 °C — 20 min / 4.5 h |
| Key properties | characteristic bond strength to B25 concrete (hammer drilling, floor, dry substrate): non-cracked τn,urc 13.2 / 13.2 / 13.2 / 13 / 13 / 12.7 N/mm² (M8 / M10 / M12 / M16 / M20 / M24), cracked τn,rc 3.6 / 3.6 / 3.6 / 3.5 / 3.4 / 3.3 N/mm²; factor for actual concrete strength ψc from 1.00 (B25) to 1.04 (B60); temperature range I −40…+42 °C (long-term up to +25 °C); tested for static and quasi-static loads |
| Shelf life | 12 months from the date of manufacture; storage at +5…+25 °C in closed packaging, in dry heated premises, no closer than 1 m to heating appliances, do not freeze |
| Standards | STO 17523759-032-2025; certificate of conformity SDS “SMIK” No. RU.SMIK.001.N.00560 valid from 27.03.2026 to 26.03.2029; state registration certificate; design per SP 513.1325800.2022 |
Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.
Other materials by UTECH
UTECH
UTECH HITRE 500 chemical bonded anchor — epoxy anchor for rebar and studs
Epoxy bonded anchor for M8–M36 studs and rebar in cracked and non-cracked concrete, including water-filled holes; installation from −10 °C.
Price on request
UTECH
UTECH ICE 500 chemical bonded anchor — acrylate anchor for installation in frost
Rapid-hardening acrylate anchor for M8–M24 studs and rebar in dry concrete at substrate temperatures down to −25 °C; 300 ml tube.
Price on request