Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Lyuks Emal Gloss — lightfast polyurethane floor enamel
ELAKOR

Elakor-PU Lyuks Emal Gloss — lightfast polyurethane floor enamel

Polyurethane floors

The acrylic-urethane Lyuks enamel does not yellow under ultraviolet — lightfastness per ISO 9370-2017 is 7 (“excellent”) — and is suitable for floors, walls, tanks and swimming pools, including outdoors and in direct contact with water. It is tinted to any colour from the “Elakor” or RAL charts, applied in 2–3 coats over polyurethane primers and used as a protective topcoat over other polymer coatings. According to the state registration certificate, the enamel is permitted in healthcare institutions, sterile and clean rooms and food plants; frost resistance at −60 °C is at least 75 cycles.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane floors
Useproduction workshops, warehouses and logistics, car parks and ramps, retail and public premises, food and pharmaceutical, wet rooms, outdoor areas, chemically resistant, decorative
Basetwo-component polyurethane lightfast weather-resistant paint; acrylic-urethane prepolymers, organic solvents, pigments, functional additives
Colourany colours, tinting to the “Elakor” or “RAL” charts; gloss finish
Packaging“A” + “B” = kit 18 kg + 3 kg = 21 kg
Application methodColoured paint-on coatings for floors, walls, structures, tanks, swimming pools; UV-protective topcoats over polymer (including anti-corrosion) coatings; decorative coatings with chips, flakes, glitter; quartz-filled and anti-slip coatings. Applied to surfaces primed with “Elakor-PU” polyurethane primers (concrete, screed, tile, metal, wood, epoxy and PU coatings). Brushes, rollers (12-14 mm nap), airless (without thinner) or air spraying (5-10% xylene or solvent); paint-on coatings 2-3 coats. Relative air humidity not more than 80%; surface moisture not more than 4 wt%; 3°C above the dew point.
Application temperatureair and surface: from +5°C to +22°C; material: from +15°C to +22°C
Curingpot life of the mix at +20°C at least 40 min; drying to degree 3 at +20°C, relative air humidity 65% not more than 1 h; forced drying up to +80°C (not more than 10 min to degree 3); drying between coats at +15…20°C – 8-12 h, but not more than 24 h; after application at +15…20°C: foot traffic – 3 days, full mechanical load – 7 days, full chemical load – 14 days
Key propertiesmix viscosity VZ-4 20-25 s; solids content at least 54%; density 1.01-1.03 kg/l; service temperature range at relative air humidity up to 80% from -60°C to +100°C, at relative air humidity above 80% from -40°C to +80°C; film water absorption not more than 0.1%; film tensile strength at least 27 MPa; elongation at break at least 20%; impact strength (U-2M) direct 100 cm, reverse 50 cm; flexibility not more than 2 mm; lightfastness 7 (excellent) per ISO 9370-2017; Taber abrasion CS-10, 1000 g, 28 days – 24 mg; resistance to climatic factors 1 point (GOST 9.401 method 2); frost resistance at -60°C at least 75 cycles; fire hazard class KM1; Shore D at 28 days 73-75; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumptionpaint-on coatings: 2-3 coats, 100-150 g/m² per coat; sealing coat of quartz-filled coatings: 1-2 coats, up to 600 g/m² per coat
Shelf life8 months in the manufacturer's original packaging; store and transport at temperatures from -30°C to +25°C

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR