Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Lyuks Grunt — lightfast transparent polyurethane primer
ELAKOR

Elakor-PU Lyuks Grunt — lightfast transparent polyurethane primer

Floor primers

The Lyuks line primer does not yellow in light, so it is used under the transparent lightfast varnish “Elakor-PU” Lyuks and as a stand-alone UV-resistant concrete impregnation, including outdoors. The material is suitable for concrete, terrazzo, breccia, tile, stone, slate and brick; 1–2 coats are applied under a coating, 2–4 coats as an impregnation until a uniform sheen. The mix has a pot life of at least 120 minutes, adhesion to B30 concrete is 2.4 MPa; according to the technical data sheet, the primer is approved for food and pharmaceutical plants and children’s and healthcare institutions.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typefloor primers
Useretail and public premises, food and pharmaceutical, outdoor areas
Baselightfast transparent two-component polyurethane primer; urethane prepolymers, organic solvents, functional additives
Colourtransparent amber liquid; transparent film
Packaging“A” + “B” = kit 16.8 kg + 1.4 kg = 18.2 kg
Application methodPriming of concrete and sand-concrete floors and other mineral surfaces (concrete, terrazzo, breccia, tile, stone, slate, brick) under the transparent lightfast varnish “Elakor-PU” Lyuks; transparent UV-resistant impregnations of concrete. Concrete not lower than M200, cured for at least 28 days, moisture not more than 4 wt%, waterproofing against groundwater. Polyamide (nylon) roller, 12-16 mm nap; under a coating 1-2 coats until it looks like wet concrete, as an impregnation 2-4 coats until a uniform sheen. Relative air humidity not more than 80%; 3°C above the dew point.
Application temperaturesurface and air: optimum +15°C…+20°C; permissible +5°C…+25°C; materials: optimum +15°C…+20°C, permissible +5°C…+25°C
Curingpot life after mixing at least 120 min; drying to degree 3 at +20°C not more than 6 h; drying between coats 3-8 h depending on temperature and humidity
Key propertiesA:B ratio by weight 12:1; solids content at least 30%; density 0.94 g/cm³; service temperature range from -60°C to +80°C; water absorption not more than 0.1%; film tensile strength at least 27 MPa; elongation at least 70%; impact strength at least 100 cm; Shore D 50-55 relative units; flexibility not more than 1 mm; adhesion to concrete B30 2.4 MPa (failure in concrete); Taber abrasion, 1 kg – 7 mg; fire hazard class KM1; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumption120-200 g/m² per coat depending on the absorbency of the substrate
Shelf life8 months in the manufacturer's original packaging; store and transport at temperatures from -30°C to +25°C
StandardsCertificate of conformity (fire safety); Certificate of conformity; Approval for use in children's and healthcare institutions; NIKIMT report “Decontaminability and radiation resistance”.

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR