Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Emal-2K/100 Smooth — solvent-free smooth polyurethane enamel
ELAKOR

Elakor-PU Emal-2K/100 Smooth — solvent-free smooth polyurethane enamel

Polyurethane floors

Unlike the textured version, this two-component enamel forms an even glossy film and is also applied in a single coat. It is used on floors, walls, structures and products made of concrete, sand-cement, tile, wood, metal and plastic after priming with “Elakor” compounds. Elongation is at least 40 %, Shore D hardness 40–50, Taber abrasion 18 mg; the optimum application temperature is +15…+20 °C, permissible from +5 to +25 °C.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane floors
Useproduction workshops, warehouses and logistics, car parks and ramps, retail and public premises, food and pharmaceutical, chemically resistant, wet rooms
Basetwo-component polyurethane enamel, smooth, without organic solvents (odourless during application); composition: urethane prepolymers, hardener, pigments, fillers, functional additives
Colourcoloured; gloss
PackagingComp. “A” + Comp. “B” = Kit: 10 kg + 5 kg = 15 kg; 20 kg + 10 kg = 30 kg
Application methodColoured protective and decorative smooth paint-type coatings for floors, walls, structures, products. On surfaces prepared and primed with “Elakor” primers: concrete, sand-cement, levelling compounds, tile, brick, slate; wood, parquet, plywood, fibreboard, particleboard; metal and plastic. Applied in 1 coat with adjustment of consumption (thickness): medium-pile rollers (12-14 mm nap), brushes, airless spraying. Concrete at least M200, cured for at least 28 days, moisture not more than 4 wt%, relative air humidity not more than 80%, dew point +3°C.
Application temperaturesurface and air: optimum +15°C…+20°C; permissible +5°C…+25°C; material temperature: +15°C…+20°C
Curingpot life of the mix on the surface at (20±2)°C at least 30 min; drying to degree 3 at (20±2)°C – not more than 8 h
Key propertiesA:B ratio by weight 2:1 (may vary, the exact ratio is on the label of component “A”); solids content ~100%; mix density 1.20±0.02 kg/l; service temperature -60°C ... +80°C, short-term (up to 30 min) up to +140°C; film tensile strength at least 12 MPa; elongation at least 40%; impact strength (U-2M) 100 cm; flexibility (bend test) not more than 2 mm; Shore D at 28 days 40-50; Taber abrasion SC-10, 1000 g, 28 days – 18 mg; gloss at 60° 80-95 (gloss); fire hazard class KM2; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, fuels and lubricants, organic solvents, petrol, diesel fuel
Layer thickness0.2-0.8 mm in 1 coat depending on consumption
Consumption1.20 kg/m² per 1 mm
Shelf life8 months in the manufacturer's original packaging; store and transport at temperatures from 0°C to +25°C

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR