Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Lyuks Lak-R/UFB Matt — matt varnish with UV filter
ELAKOR

Elakor-PU Lyuks Lak-R/UFB Matt — matt varnish with UV filter

Sealers and topcoats

The matt version of the varnish with a UV filter removes the gloss from a polymer floor and blocks ultraviolet, protecting the underlying coating. The two-component material, mixed 7:1, is applied in two coats with a velour roller, and with a brush at abutments, at surface, air and material temperatures from +5 to +20 °C. The film withstands a tensile stress of at least 40 MPa, works from −60 to +100 °C, fire hazard class KM1 (V1, D1, T2, RP1); use in healthcare institutions and food plants is permitted by the state registration certificate.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typevarnishes and topcoats
Usefood and pharmaceutical, wet rooms, outdoor areas, chemically resistant, decorative
Basetwo-component polyurethane varnish, lightfast, with UV filter
Colourtransparent, colourless (film); matt
PackagingComp. “A” + Comp. “B” = Kit: 7 kg + 1 kg = 8 kg; 14 kg + 2 kg = 16 kg
Application methodTopcoat to protect polyurethane and epoxy coatings from ultraviolet and to increase chemical resistance and wear resistance; UV protection of parquet, wood, plastic; transparent impregnations for concrete, stone, brick, tile. “Velour-Wool” roller (5 mm nap), brushes at abutments; 2 coats, rolling in two mutually perpendicular directions. Relative air humidity not more than 80%; surface 3°C above the dew point; surface temperature difference not more than 3°C during application and for a day afterwards; waterproofing against groundwater on the lowest floor.
Application temperaturesurface, air, materials: +5°C…+20°C
Curingdrying to degree 3 at +20°C not more than 10 h; drying of the 1st coat 6-12 hours, but not more than 24 hours; after application at +15…20°C: foot traffic – 3 days, full mechanical load – 7 days, full chemical load – 14 days
Key propertiesA:B ratio 7:1; mix viscosity VZ-4 10-12 s; solids content at least 32%; density 0.92 kg/l; service temperature range from -60°C to +100°C (up to 30 min – up to +150°C); water absorption not more than 0.1%; film tensile strength at least 40 MPa; elongation at least 8%; impact strength at least 100 cm; Shore D at 28 days 70-74; flexibility not more than 1 mm; Taber abrasion CS-10, 1 kg – 5 mg; lightfastness 7 / excellent (ISO 9370-2017); fire hazard class KM1 (V1, D1, T2, RP1); chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumption2 coats; consumption per coat: to change surface gloss 50-60 g/m², to seal chips, flakes, glitter 60-70 g/m²
Shelf life8 months in the manufacturer's original packaging; store and transport at temperatures from -30°C to +25°C

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR