Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Emal-60 SK PROF — polyurethane enamel of the professional line
ELAKOR

Elakor-PU Emal-60 SK PROF — polyurethane enamel of the professional line

Polyurethane floors

The professional version of Emal-60 keeps the semi-gloss film with a gloss of 45–55 %, and according to the technical data sheet it has higher adhesion: 6.2 MPa to M750 (B55) concrete with failure in concrete and 63.7 MPa to St3 steel. The paint is applied by roller, brush or airless spraying in two coats over a primed substrate to make coloured, quartz-filled, anti-slip and decorative floors. Application is permitted from −30 to +25 °C, fire hazard class KM1, and it is approved, among other uses, for food and pharmaceutical plants.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane floors
Useproduction workshops, warehouses and logistics, car parks and ramps, retail and public premises, chemically resistant, wet rooms, food and pharmaceutical, decorative
Basemoisture-curing one-component polyurethane paint for professional use; composition: urethane prepolymers, organic solvents, pigments, functional additives
Colourbase colour – grey (RAL7035 or 7040); tinted to the RAL chart; semi-gloss
Packagingmetal pail 22 kg
Application methodColoured paint-on PU floors, quartz-filled and anti-slip coatings, decorative floors with chips, flakes, glitter; protection of concrete and wood. On surfaces primed or filled with PU/epoxy materials. Rollers, brushes, airless spraying; 2 coats (additional coats permitted). Surface moisture not more than 4 wt%, relative air humidity not more than 80%, dew point +3°C.
Application temperatureair and surface: from -30°C to +25°C; material temperature: from +10°C to +25°C
Curingdrying to degree 3 at +20°C – not more than 6 h; drying between coats above 0°C – 4-8 h, but not more than 24 h; below 0°C – 16-24 h, but not more than 48 h
Key propertiesviscosity (VZ-4 cup) at +20°C 30-45 s; solids content at least 59%; density 1.07 g/cm³; service temperature range from -60°C to +120°C (up to 30 min – up to +180°C); water absorption not more than 0.1%; film tensile strength at least 65 MPa; elongation at least 20%; impact strength (U-2M) 100 cm, reverse impact 100 cm; hardness (ME-3/TML) at least 0.6/0.4 relative units; Shore D at 28 days 75-78; flexibility not more than 1 mm; gloss at 60° 45-55% (semi-gloss); adhesion to concrete M750 (B55) 6.2 MPa (failure in concrete, GOST 22690-88), to magnesia concrete 3.68 MPa, to St3 steel 63.7 MPa (GOST 15140); abrasion resistance 37 kg/µm (method A), 1.5 (0.00015) g/m² (g/cm²) (method B); Taber abrasion CS-10, 1000 g, 28 days – 9 mg; resistance to climatic factors 1 point; frost resistance at -60°C at least 75 cycles; fire hazard class KM1; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumption120-170 g/m² per coat (depends on surface roughness), 2 coats; for colours RAL 1016, 1018, 2003, 2004, 2008, 2009, 2011, 3000, 3001, 3002, 3013, 3016, 3020, 3028, 3031, 6037 (insufficient hiding power) – first 1 coat of Emal-60 White, consumption 100-120 g/m²
Shelf life6 months in the manufacturer's original packaging; store and transport at temperatures from -40°C to +25°C
StandardsCertificate of conformity (fire safety); Certificate of conformity; Approval for use in children's and healthcare institutions; NIKIMT report “Decontaminability and radiation resistance”.

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR