LEVL (INGRI)
LEVL Top Corund — corundum topping for heavily loaded floors
Hardening dry mix with corundum for concrete floors under very significant mechanical loads; compressive strength at least 90 MPa.
Price on request
LEVL (INGRI)
LEVL Coat 218 — high-gloss epoxy primer-enamel for floors
LEVL Coat 218 high-gloss epoxy enamel is intended for floors with sanitary and hygiene requirements in the food, pharmaceutical and chemical industries, healthcare and education. The coating is thin-layer: it does not level the substrate, but it bridges fine cracks and can be applied in self-priming mode. It is applied with a velour roller or brush in two coats; the compound is also suitable for covered unheated premises and car parks. Taber abrasion is up to 65 mg, service from −25 to +60 °C.
Specifications
| Manufacturer | LEVL (INGRI) — OOO “Ingri”, Saint Petersburg |
|---|---|
| Type | epoxy floors |
| Use | production workshops, food and pharmaceutical, retail and public buildings, warehouses and logistics, car parks and ramps, decorative |
| Base | epoxy resin + cycloaliphatic hardener |
| Colour | RAL colours; smooth-textured high-gloss finish |
| Packaging | 20 kg kits (A and B in two containers); A : B = 5 : 1 (by weight) |
| Application method | thin-layer protective, decorative and wear-resistant floor paint (does not level the substrate) where sanitary and hygiene requirements apply; over LEVL Coat 101/104 Rapid (textured) or 108/118 (smooth) primer, or self-priming with 218 (0.2 kg/m²); velour roller or brush, 2 coats; possible in covered unheated premises and car parks |
| Application temperature | air +10…+30 °C (recommended +17…+23 °C); substrate +10…+30 °C (recommended +17…+25 °C); material +15…+25 °C; air humidity up to 80 %; substrate moisture no more than 5 % by weight; 3 °C above the dew point |
| Curing | light loads: +10 °C 32 h, +20 °C 16 h, +30 °C 12 h; foot traffic 6 / 3 / 2 days; full strength gain 10 / 7 / 5 days; next coat after 24–48 h at 20 °C; drying to degree 3 no more than 8 h |
| Key properties | Taber abrasion (CS10 / 1000 g / 1000 rev.) no more than 65 mg; cross-cut adhesion no more than grade 1; density 1.13 ± 0.05 g/cm³; non-volatile content at least 74 %; bridges fine cracks; pot life at +23 °C at least 60 min; service temperature from −25 to +60 °C |
| Consumption | 150–200 g/m² per coat; 2 coats: 0.3–0.4 kg/m² (finish in the system 0.4 kg/m²; self-priming 0.2 kg/m²; 3 coats permitted when self-priming) |
| Shelf life | 12 months from the date of manufacture; storage at +5…+25 °C |
| Standards | TU 20.30.12-069-94613022-2019; works per SP 29.13330.2011 and SP 71.13330.2017 (Table 8.12); test methods GOST 31992.1, GOST R 31939, GOST 19007, GOST 31149 |
Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.
Other materials by LEVL (INGRI)
LEVL (INGRI)
LEVL Coat 304 RAPID — fast-curing epoxy self-levelling floor
Coloured epoxy self-levelling floor for warehouses, workshops and car parks that takes full load after about 12 hours at +20 °C.
Price on request
LEVL (INGRI)
LEVL RemTixo Rapid AF — thixotropic repair compound for work in frost
Rapid-hardening fibre-reinforced mix for repairing concrete in cold stores, on roads and airfields at air temperatures down to −10 °C.
Price on request
LEVL (INGRI)
LEVL Coat 501 — clear epoxy binder for decorative floors
Binder for floors and screeds with coloured quartz sand: clear, gloss, chemically resistant; fire hazard class KM2.
Price on request
LEVL (INGRI)
LEVL CemPol 40 — thin-layer self-levelling screed for indoor use
Rapid-hardening self-levelling coating on special cements for indoor use only; compressive strength 40 MPa, flexural strength 8 MPa.
Price on request
LEVL (INGRI)
LEVL CemPol 30 — low-shrinkage cement screed and industrial floor
Mortar mix for a finishing cementitious floor or a base under self-levelling coatings; compressive strength 40 MPa, non-combustible (NG, KM-0).
Price on request