LEVL (INGRI)
LEVL Coat 104 RAPID — fast epoxy primer for polymer floors
Epoxy primer with accelerated curing under LEVL floors: foot traffic after 6 hours, full strength in about 12 hours at +20 °C.
Price on request
LEVL (INGRI)
LEVL Top WL — mortar topping for restoring old concrete floors
When there is no fresh concrete and a worn floor needs restoring, LEVL Top WL is used: a mortar mix laid wet-on-wet over a bonding layer on the old substrate. The mortar is spread with a squeegee or straightedge, floated with a power trowel and protected with LEVL Cure 100; it can be delivered by a mortar/concrete pump. Compressive strength is at least 70 MPa, flexural strength at least 8 MPa, abrasion up to 0.4 g/cm², service temperature from −40 to +70 °C. It suits workshops, warehouses, car parks and outdoor areas.
Specifications
| Manufacturer | LEVL (INGRI) — OOO “Ingri”, Saint Petersburg |
|---|---|
| Type | dry-shake toppings |
| Use | production workshops, warehouses and logistics, car parks and ramps, outdoor areas |
| Base | dry cement mix (mortar type, applied wet-on-wet over a bonding layer) |
| Colour | light grey, red, green, dark grey |
| Application method | thin high-strength coating over old concrete: bonding layer of LEVL Prime EP + Silverbond 30 + quartz sand, then LEVL Top WL mortar by squeegee/straightedge, floating with a power trowel; LEVL Cure 100; can be delivered by a mortar/concrete pump; indoors and outdoors |
| Application temperature | +5…+30 °C (ambient and substrate); substrate: concrete at least B22.5, pull-off strength at least 1.5 MPa |
| Key properties | Compressive strength after 28 days at least 70 MPa; flexural strength at least 8 MPa; abrasion (wear) no more than 0.4 g/cm²; bond to substrate (with LEVL Prime EP) at least 1.5 MPa; mechanical loads: significant; service temperature from −40 °C to +70 °C |
| Layer thickness | 5–15 mm (system example: 10.0 mm) |
| Consumption | 2.1 kg/m² per 1 mm of thickness (theoretical); at 10 mm: 21.0 kg/m² + water 2.52 kg/m² |
| Shelf life | 12 months from the date of manufacture |
| Standards | TU 23.64.10-063-94613022-2018; GOST 310.4, GOST 13087, GOST 31356; SP 29.13330.2011 |
Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.
Other materials by LEVL (INGRI)
LEVL (INGRI)
LEVL PoliCem PU 05 — polyurethane-cement primer for PoliCem systems
Three-component primer for sealing concrete pores under polyurethane-cement floors in food, pharmaceutical and chemical production.
Price on request
LEVL (INGRI)
LEVL Concrete Strong 7 — lithium impregnation for hardening concrete
Lithium silicate impregnation for dustproofing and hardening concrete floors and polished concrete; no organic solvents.
Price on request
LEVL (INGRI)
LEVL Coat 358 — highly elastic polyurethane self-levelling floor
Single-layer PU coating that bridges concrete cracks, for workshops, warehouses, energy and transport facilities; elongation at break from 50 %.
Price on request
LEVL (INGRI)
LEVL Top Corund Premium ST — quartz-corundum topping with low abrasion
Topping with quartz and corundum aggregate for workshops, warehouses and car parks under very significant loads; abrasion (wear) no more than 0.15 g/cm².
Price on request
LEVL (INGRI)
LEVL CemPol 10 — cementitious floor for heavy vehicle traffic
Stiff mortar mix for new and repaired floors of ports, container yards and car parks; strength 60 MPa, frost resistance F1 200.
Price on request