Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
Elakor-PU Emal-60 Gloss — gloss polyurethane floor paint
ELAKOR

Elakor-PU Emal-60 Gloss — gloss polyurethane floor paint

Polyurethane floors

The gloss modification of Emal-60 forms a film with a gloss of 70–80 % and is used for coloured paint-on floors, quartz-filled and anti-slip coatings, and floors with chips, flakes and glitter. It is applied in two coats over surfaces primed or filled with polyurethane and epoxy materials — on concrete of grade not lower than M100 or on wood. Shear adhesion to St3 steel is 63.7 MPa, frost resistance at −60 °C is at least 75 cycles; the film yellows in light, but its protective properties do not change.

Specifications

ManufacturerElakor — OOO “TEOKHIM-PROM”, Moscow Region
Typepolyurethane floors
Useproduction workshops, warehouses and logistics, car parks and ramps, retail and public premises, chemically resistant, wet rooms, food and pharmaceutical, decorative
Basemoisture-curing one-component polyurethane paint; composition: urethane prepolymers, organic solvents, functional additives
Colourbase colour – grey (RAL7035 or 7040); tinted to the RAL chart; gloss; yellows in light
Packagingmetal pail 20 kg
Application methodColoured paint-on PU floors, quartz-filled and anti-slip coatings, decorative floors with chips, flakes, glitter; protection of concrete and wooden surfaces. On surfaces primed or filled with PU/epoxy materials. Rollers, brushes (solvent-resistant), airless spraying; 2 coats (additional coats permitted). Concrete at least M100, cured for at least 28 days, moisture not more than 4 wt%, relative air humidity not more than 80%, dew point +3°C.
Application temperaturesurface and air: -30°C…+25°C; material temperature: +10°C…+25°C
Curingdrying to degree 3 at +20°C – not more than 6 h; drying between coats above 0°C – 4-8 h, but not more than 24 h; below 0°C – 16-24 h, but not more than 48 h
Key propertiesviscosity (VZ-4 cup) at +20°C 30-45 s; solids content at least 59%; density 1.07 g/cm³; service temperature range from -60°C to +120°C (up to 30 min – up to +180°C); water absorption not more than 0.1%; film tensile strength at least 65 MPa; elongation at least 20%; impact strength (U-2M) 100 cm, reverse impact 100 cm; hardness (ME-3/TML) at least 0.6/0.4 relative units; flexibility not more than 1 mm; gloss at 60° 70-80% (gloss); adhesion to concrete M350 (B25) 1.55 MPa (failure in concrete), to magnesia concrete 3.68 MPa, shear on St3 steel 63.7 MPa (GOST 15140); abrasion resistance 37 kg/µm (method A), 1.5 (0.00015) g/m² (g/cm²) (method B); specific Taber abrasion, 1 kg – 0.011 g; resistance to climatic factors 1 point; frost resistance at -60°C at least 75 cycles; fire hazard class KM1; chemical resistance: water, salt and alkali solutions of any concentration, acid solutions up to 10-20%, oils and fats of all kinds, organic solvents, petrol, diesel fuel
Consumption120-170 g/m² per coat (depends on surface roughness), 2 coats; for colours RAL 1016, 1018, 2003, 2004, 2008, 2009, 2011, 3000, 3001, 3002, 3013, 3016, 3020, 3028, 3031, 6037 (insufficient hiding power) – first 1 coat of Emal-60 White, consumption 100-120 g/m²
Shelf life6 months in the manufacturer's original packaging; store and transport at temperatures from -40°C to +25°C
StandardsCertificate of conformity (fire safety); Certificate of conformity; Approval for use in children's and healthcare institutions; NIKIMT report “Decontaminability and radiation resistance”.

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by ELAKOR