Supply across Uzbekistan and to Kyrgyzstan, Tajikistan and Turkmenistan +998 93 815 00 53 Telegram sale@coatix.uz
LEVL Coat 303 — epoxy self-levelling floor, smooth and textured
LEVL (INGRI)

LEVL Coat 303 — epoxy self-levelling floor, smooth and textured

Epoxy floors

The main epoxy self-levelling floor of the range is LEVL Coat 303. It is used to make smooth and textured, unfilled and highly filled coatings over LEVL Coat 101, 102 W, 104 Rapid, 108 and other primers. Shore D hardness is at least 75, compressive strength 63 MPa, flexural 35 MPa; the coating is resistant to aggressive media, process water and bacteriological attack. It is used in offices, retail, healthcare, education, pharmaceutical and chemical plants, warehouses, covered car parks and rooms with a “wet cycle”.

Specifications

ManufacturerLEVL (INGRI) — OOO “Ingri”, Saint Petersburg
Typeepoxy floors
Useretail and public buildings, food and pharmaceutical, chemically resistant, warehouses and logistics, production workshops, car parks and ramps, wet rooms
Baseepoxy resin (two-component composition)
ColourRAL colours; uniform gloss finish
Packagingkits of 2.4 and 27 kg; A : B = 4.62 : 1.00 (by weight)
Application methodself-levelling and highly filled, smooth and textured floor coatings over LEVL Coat 101 / 102 W / 103 / 104 Rapid / 108 / 118 primer: pouring, squeegee or notched trowel, rolling with a spiked roller; filling with quartz sand 3.0 : 1.0; textured: broadcast to excess with 0.3–0.9 mm sand and a finishing coat by roller
Application temperatureair and substrate +10…+30 °C (recommended +17…+23 °C); material +15…+25 °C; air humidity no more than 80 %; substrate moisture no more than 5 % (primers 101/103/104 Rapid/108/118) or no more than 10 % (primer 102 W); 3 °C above the dew point
Curinglight loads / recoat interval: +10 °C ~32 h, +23 °C ~16 h, +30 °C ~12 h; foot traffic: ~6 / ~3 / ~2 days; full strength gain: ~10 / ~7 / ~5 days; next coat no earlier than 16 h and no later than 48 h at 23 °C
Key propertiesShore D hardness (7 days) at least 75; ultimate compressive strength (7 days) at least 63 MPa; flexural at least 35 MPa; tensile strength at break at least 16 MPa; adhesion to concrete at least 2.5 MPa (failure in the concrete); Taber abrasion (CS10 / 1000 g / 1000 rev.) no more than 55 mg; density 1.67 ± 0.1 g/cm³; non-volatile content at least 95 %; pot life +10 °C ~60 min, +20 °C ~30 min, +30 °C ~15 min; service temperature from −10 to +60 °C (highly filled: short-term up to +90 °C); chemical resistance: on request from Ingri
Layer thicknessself-levelling unfilled 1.5–3.0 mm; self-levelling filled (+33 % sand) 1.5–3.0 mm; highly filled 3–12 mm
Consumptionsmooth unfilled 2 mm: 3.34 kg/m²; smooth filled 2 mm: 2.75 kg/m² + quartz sand 0.1–0.3 mm 0.92 kg/m²; textured highly filled 6 mm: 3.24 kg/m² + broadcast sand 0.3–0.9 mm 6.84 kg/m² + finishing coat 1.01 kg/m²; theoretically per 1 mm: unfilled 1.67 kg/m², filled (3.0 : 1.0) 1.83 kg/m²
Shelf life12 months from the date of manufacture; storage at +5…+25 °C
StandardsTU 2257-006-94613022-2006; works per SP 29.13330.2011 and SP 71.13330.2017; test methods GOST 31992.1, GOST R 31939, GOST 24621, GOST 11262, GOST 28574

Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.

Other materials by LEVL (INGRI)