GLIMS
GLIMS® PRO Cure-A — curing impregnation for concrete
Waterborne acrylate curing impregnation: retains moisture in fresh concrete, dustproofs and hardens finished floors.
Price on request
GLIMS
GLIMS® PRO CRT-40 — thixotropic R3 mortar for local structural repair
For local structural repair of concrete and reinforced concrete with strength not lower than B20, GLIMS® PRO CRT-40 is suitable: a thixotropic mortar of class R3 to GOST R 56378-2015. It is placed without formwork on vertical, inclined, horizontal and overhead surfaces of bridges, bridge spans, tunnels, car parks, viaducts and equipment foundations, as well as port and hydraulic structures, chimneys and cooling towers. Compressive strength is 15 MPa after one day and 40 MPa after 28 days, adhesion from 1.5 MPa, W12, F2 300.
Specifications
| Manufacturer | GLIMS — AO GLIMS-Production, Podolsk |
|---|---|
| Type | thixotropic repair mortars |
| Use | bridges and overpasses, tunnels and metro, hydraulic structures and dams, industrial buildings, equipment foundations |
| Base | Non-shrink thixotropic mix of special cements, graded sand, mineral aggregates and chemical admixtures, with polymer fibre |
| Colour | grey |
| Packaging | bag 25 kg |
| Application method | Local structural repair of concrete and reinforced concrete (of strength not lower than B20) on vertical, inclined, horizontal and overhead surfaces without formwork: elements of bridges, bridge spans, tunnels, car parks, viaducts, industrial floors, equipment foundations; port and hydraulic structures |
| Key properties | maximum aggregate size: 3 mm; mixing water: 0.16–0.17 l per 1 kg; pot life: 30 min; adhesion: ≥1.5 MPa; modulus of elasticity: ≥15,000 MPa; compressive strength at 1 / 28 days: ≥15 / ≥40 MPa; flexural strength: ≥8 MPa; frost resistance: F2 300; water impermeability: W12 |
| Shelf life | 12 months from the date of manufacture in undamaged original factory packaging in a dry room |
| Standards | class R3 to GOST R 56378-2015; TU 5745-010-40397319-2003 No. 0500/2 |
Data from the manufacturer’s technical data sheet. The coating system, number of coats and quantity are selected for your project on request.
Other materials by GLIMS
GLIMS
GLIMS® CRT-40 AF — winter thixotropic R3 mortar for repair at −15…+15 °C
Coarse-grained thixotropic R3 mortar for repairing concrete, steps and stair flights at temperatures from −15 to +15 °C; W12, F2 300.
Price on request
GLIMS
GLIMS® PRO CRP-40 0.5 — finishing thixotropic R3 mortar for restoring geometry
Non-shrink finishing R3 mortar for finishing concrete and stone surfaces and repairing dormant cracks; contact with drinking water is permitted.
Price on request
GLIMS
GLIMS® PRO ANCHOR-T — R4 anchoring grout with aggregate up to 0.5 mm for small gaps
Thin-layer non-shrink flowable R4 grout for anchoring in small gaps and hard-to-reach places; aggregate up to 0.5 mm, 60 MPa.
Price on request
GLIMS
GLIMS® PRO FS TOP 450 — corundum topping for industrial floors
Dry corundum hardening mix for concrete floors under extreme mechanical, impact and abrasive loads; up to +120 °C.
Price on request
GLIMS
GLIMS® PRO CRT-20 — thixotropic R2 mortar for non-structural repair
Thixotropic R2 mortar with fibre for filling voids, caulking joints, repairing manholes and tanks; compressive strength from 20 MPa at 28 days, W8.
Price on request