BIRSS
BIRSS 30 Spets — cement-polymer mix for vertical and overhead surfaces
Non-shrink fine-grained mix for non-structural repair and levelling of concrete on vertical and overhead areas; workability is retained for 60 minutes.
Price on request
Thixotropic repair mortars
A thixotropic repair mortar turns plastic after mixing with water but does not slump, so it is applied by trowel or by spraying to vertical, inclined and overhead areas without formwork. They restore the cover and shape of columns, beams, slabs, bridge piers and spans, tunnel walls, tanks and hydraulic structures after spalling, cavities and rebar corrosion.
- fibre-reinforced R3 and R4 structural mortars, including 70–80 MPa high-strength grades and metal-fibre grades for impact and vibration;
- non-structural R2 and R3 products for voids, honeycombing and minor defects;
- fine-grained finishing mortars for levelling repaired surfaces;
- winter mortars with antifreeze admixtures that need no heating down to −20 °C, and rapid-hardening grades reaching 20 MPa in 2 hours;
- a lightweight mortar for ceilings and a thixotropic epoxy that forms a chemical-resistant coating.
To choose, give the concrete class, depth and area of damage, surface orientation and air temperature during work.
Manufacturer
BIRSS
BIRSS 59 S2 M600 — thixotropic R4 mix with microfibre for bridges and tunnels
Repair mortar with polymer microfibre for vertical and horizontal structures of bridges, tunnels and ports and potholes without formwork; W18.
Price on request
BIRSS
BIRSS 59 S2 M600 Moroz — thixotropic R4 mix with microfibre for work from −15 °C
Micro-reinforced mortar for repairing bridges, tunnels and hydraulic structures at temperatures from −15 to +5 °C; water impermeability W18.
Price on request
BIRSS
BIRSS 59 S2 M600 Moroz Uskorennaya — R4 mix gaining 20 MPa in 2 hours at +20 °C
Accelerated-hardening thixotropic mortar for repairing bridges, tunnels and joints at temperatures from −10 °C; 20 MPa after 2 hours at +20 °C.
Price on request
BIRSS
BIRSS 59 S2 M700 — thixotropic 70 MPa R4 mix for local repair
Mortar with polymer microfibre for local structural repair of bridges, tunnels and hydraulic structures; 70 MPa at 28 days.
Price on request
BIRSS
BIRSS 59 S2 M700 Moroz — 70 MPa R4 mix placed from −15 to +30 °C
Thixotropic mortar with microfibre for repairing bridges, tunnels and port structures from −15 to +30 °C; at +20 °C it reaches 70 MPa in 28 days.
Price on request
BIRSS
BIRSS RBG M500 — two-component R4 repair mix with granite aggregate
Kit of dry mix and granite aggregate for repairing ramps, bridge abutments, channels, floors and slab joints; modulus of elasticity 25,000 MPa.
Price on request
BIRSS
BIRSS RBM M400 — fibre-reinforced R3 mix for airfield and road pavements
Thixotropic repair mortar with fibre for airfield and road pavements under intensive dynamic and impact loads; class R3.
Price on request
BIRSS
BIRSS RSM Zashchitny Sloy — fine-grained R2 mix for non-structural repair
Rapid-hardening polymer-cement mix for small defects of exposed concrete, steps, stairs and fine finishing; aggregate size 0.315 mm.
Price on request
BIRSS
BIRSS RSM-1 M350 — two-component polymer-cement R3 repair system
Two-component mortar for repairing vertical, inclined and overhead concrete areas on bridges and in buildings; placing is possible from −10 °C.
Price on request
BIRSS
BIRSS RSM-1 M450 — thixotropic R4 repair mix with reinforcing fibre
Fibre-reinforced mortar for repairing bridges, tunnels, joints between precast elements and potholes without formwork; compressive 45 MPa at 28 days.
Price on request
BIRSS
BIRSS RSM-1 M450 Moroz — fibre-reinforced R4 mix for repair down to −15 °C
Thixotropic repair mix for bridges, tunnels and joints of precast structures, placed at temperatures from −15 to +5 °C.
Price on request
BIRSS
BIRSS RSM-2 M350 — thixotropic R3 mix with normal setting times
Shrinkage-compensated repair mortar for bridges, tunnels, hydraulic structures and joints of precast reinforced concrete; class R3.
Price on request
BIRSS
BIRSS RSM-2M M350 — rapid-hardening fibre-reinforced repair mix
Thixotropic mix with reinforcing fibre for structural repair of bridges, tunnels and joints of precast concrete; 15 MPa in compression after one day.
Price on request
BIRSS
BIRSS RSM-2M M450 — thixotropic R4 mix with aggregate up to 5 mm
Fibre-reinforced R4 repair mortar for bridges, tunnels and structures under dynamic loads; aggregate size up to 5 mm.
Price on request
BIRSS
BIRSS RSM-2M M550 Moroz — R4 repair mix with anti-freeze admixture
Mix for hand repair of joints, cracks and concrete defects without formwork at low and sub-zero temperatures; at +20 °C it reaches 55 MPa in 28 days.
Price on request
BIRSS
BIRSS VRS 600 — R4 repair mix for high-strength concrete structures
Fibre-reinforced thixotropic mortar for column and beam corners, balcony edges and working joints; service temperature up to +300 °C.
Price on request
BIRSS
BIRSS VRS 600 Moroz — fibre-reinforced R4 mix for high-strength concrete in frost
Thixotropic mix with fibre for columns, beams and balconies at temperatures from −15 to +5 °C; in frost it reaches 55 MPa in compression in 28 days.
Price on request
Kalmatron
Gidrobeton KRIO-2 — thixotropic repair mortar for work in frost
Rapid-hardening thixotropic mix for repairing concrete and masonry at air temperatures down to −10 °C; at least 30 MPa compressive after one day.
Price on request
Kalmatron
Gidrobeton SRG-1 — cement-based waterproofing repair mortar
Cementitious mix for repairing and waterproofing concrete, masonry, joints and screeds in tanks and treatment plants; compressive strength at least 50 MPa.
Price on request
Kalmatron
Gidrobeton SRG-2 — fine-grained waterproofing repair mortar
Fine-grained cementitious mix for repairing and waterproofing concrete by hand or by dry-mix shotcreting; watertightness at least 14 atmospheres.
Price on request
Kalmatron
Gidrobeton SRG-4 — thixotropic class R3 repair mortar
Thixotropic non-shrink class R3 mix for repairing and levelling concrete and reinforced concrete structures; watertightness W18.
Price on request
Kalmatron
Gidrobeton SRG-F1 — fibre-reinforced shrinkage-compensated repair mortar
Repair mix with polypropylene fibre and compensated shrinkage for concrete defects in interior and exterior work; bond 2.0 MPa.
Price on request
Kalmatron
Gidrobeton SRG-F2 — fine-grained fibre-reinforced mortar for repair and shotcrete
Fine-grained mix with fibre for repairing and waterproofing concrete by hand or by dry-mix shotcrete; watertightness 14 atmospheres, 300 cycles.
Price on request
GLIMS
GLIMS® CRT-40 AF — winter thixotropic R3 mortar for repair at −15…+15 °C
Coarse-grained thixotropic R3 mortar for repairing concrete, steps and stair flights at temperatures from −15 to +15 °C; W12, F2 300.
Price on request
GLIMS
GLIMS® PRO CRP-40 0.5 — finishing thixotropic R3 mortar for restoring geometry
Non-shrink finishing R3 mortar for finishing concrete and stone surfaces and repairing dormant cracks; contact with drinking water is permitted.
Price on request
GLIMS
GLIMS® PRO CRT-20 — thixotropic R2 mortar for non-structural repair
Thixotropic R2 mortar with fibre for filling voids, caulking joints, repairing manholes and tanks; compressive strength from 20 MPa at 28 days, W8.
Price on request
GLIMS
GLIMS® PRO CRT-40 — thixotropic R3 mortar for local structural repair
Thixotropic R3 mortar for repairing concrete of B20 and above on walls and ceilings without formwork: bridges, tunnels, car parks; 40 MPa at 28 days.
Price on request
GLIMS
GLIMS® PRO CRT-60 — thixotropic R4 mortar for structures under increased loads
Thixotropic R4 repair mortar for bridges, tunnels, cooling towers and flue ducts under static and dynamic loads; 60 MPa, W18.
Price on request
Pakol
Pakol Epoks T — thixotropic epoxy compound for repair and levelling
Thixotropic epoxy mortar for filling spalls and gouges with a chemically resistant coating on concrete, stone and brick; 95.0 MPa compressive at 7 days.
Price on request
Pakol
Pakol Finish — skim-coat mix for finish repair and levelling
Finely dispersed cementitious skim coat for finish repair and levelling of concrete, brick and stone walls and ceilings; bond to substrate 2.8 MPa.
Price on request
Pakol
Pakol Remontny 400 K — non-structural thixotropic R3 mortar with 3 mm aggregate
Non-structural filling of large spalls and gouges on walls, columns and beams of industrial buildings: a thixotropic R3 mix with 3 mm aggregate.
Price on request
Pakol
Pakol Remontny 400 M — fine-grained thixotropic R3 mix for small spalls
R3 mortar with grain up to 1 mm for non-structural repair of small defects in columns, beams and walls of industrial buildings at temperatures from +5 °C; B30.
Price on request
Pakol
Pakol Remontny 600 K — structural thixotropic R4 mortar for bridges and tunnels
Coarse-grained thixotropic R4 mortar for repair and strengthening of bridges, tunnels, dams and tanks; F1 1000, W20, compressive 65.0 MPa after 28 days.
Price on request
Pakol
Pakol Remontny 600 KM — R4 mortar with admixtures that reduce cracking
Mix with an expansive admixture and modifiers that reduce cracking, for structural repair and strengthening of reinforced concrete; class R4, B50.
Price on request
Pakol
Pakol Remontny 600 KS — steel-fibre mortar for vibration-loaded structures
Mix with steel and polypropylene fibre for repair and strengthening of structures under dynamic and vibration loads; flexural strength 11.0 MPa (Btb8.0).
Price on request
Pakol
Pakol Remontny 600 M — fine-grained thixotropic R4 mix for walls and ceilings
Fine-grained thixotropic R4 mortar for structural repair of shallow spalls on bridges, in tunnels and on columns; watertightness W18.
Price on request
Pakol
Pakol Remontny 800 K — high-strength thixotropic B60 mortar for strengthening
Thixotropic B60 mix with a modulus of elasticity of 27.0 GPa for strengthening reinforced concrete columns, beams and walls of buildings and bridges; flexural 12.0 MPa.
Price on request
Pakol
Pakol Remontny BK — rapid-hardening thixotropic mortar for work at −10…+7 °C
Rapid-hardening thixotropic mix for urgent repair of walls, ceilings and columns at −10…+7 °C; 12.0 MPa compressive after 2 h.
Price on request
Pakol
Pakol Remontny BM — fine-grained thixotropic mortar with rapid strength gain
Fine-grained rapid-hardening thixotropic mix for urgent filling of shallow spalls at −10…+7 °C; 10.0 MPa compressive after 2 h.
Price on request
Pakol
Pakol Remontny Zima 400 K — antifreeze R3 mortar for non-structural repair
Coarse-grained R3 mix with an antifreeze admixture for non-structural repair of walls, columns and ceilings down to −10 °C without heating.
Price on request
Pakol
Pakol Remontny Zima 400 M — fine-grained antifreeze R3 mix, to −10 °C
Fine-grained R3 mix with an antifreeze admixture for filling small spalls on walls, columns and ceilings down to −10 °C without heating.
Price on request
Pakol
Pakol Remontny Zima 600 K — coarse-grained winter R4 mortar, 20.0 MPa in 2 h
Winter B45 mix for urgent filling of spalls and cavities on walls and ceilings of dams and tanks without heating down to −20 °C; 20.0 MPa after 2 h.
Price on request
Pakol
Pakol Remontny Zima 600 M — fine-grained winter R4 mortar for work down to −20 °C
Fine-grained thixotropic mortar for urgent repair of spalls and cavities on walls, columns and ceilings in frost down to −20 °C; 12.0 MPa compressive after 2 h.
Price on request
Pakol
Pakol Remontny Zima 800 K — high-strength winter B60 mortar for work to −20 °C
High-strength winter B60 mix for repairing columns, beams and overhead areas in tunnels and on bridges down to −20 °C; 55.0 MPa after just 24 h.
Price on request
INDASTRO
Profskrin RC30 PSm — fibre-reinforced finishing repair mortar with fine aggregate
Fibre-reinforced finishing mortar for repairing load-bearing, bridge and underground concrete structures; aggregate 0.315 mm, compressive strength 30 MPa at 28 days.
Price on request
INDASTRO
Profskrin RC35 — thixotropic R3 repair mortar for concrete and reinforced concrete
Thixotropic R3 cementitious mortar for structural repair of concrete and reinforced concrete in industrial buildings; compressive strength at 28 days from 35 MPa.
Price on request
INDASTRO
Profskrin RC35 Sm — fibre-reinforced mortar for repair and finishing of concrete
Fibre-reinforced mortar with sand up to 0.63 mm for repair and finishing of concrete structures of bridges, treatment plants and underground facilities; W12.
Price on request
INDASTRO
Profskrin RC40 FSm — winter finishing mortar for fine finishing of concrete
Fibre-reinforced finishing mortar for fine finishing of concrete structures in winter at temperatures from −10 to +10 °C; compressive strength 40 MPa at 28 days.
Price on request
INDASTRO
Profskrin RC40 Sm — fibre-reinforced finishing mortar, 40 MPa at 28 days
Finishing repair mortar with fibre and sand up to 0.63 mm for load-bearing, bridge and treatment structures; compressive strength from 20 MPa after one day.
Price on request
INDASTRO
Profskrin RC45 — R4 repair mortar for B30–B40 concrete structures
Thixotropic R4 mortar for repairing B30–B40 concrete and reinforced concrete structures, including walls and ceilings; compressive strength at 28 days from 45 MPa.
Price on request
INDASTRO
Profskrin RC45 F — winter thixotropic R4 mortar for work at −10…+10 °C
Winter version of the thixotropic R4 mortar for repairing B30–B40 concrete at temperatures from −10 to +10 °C; compressive strength at 28 days from 45 MPa.
Price on request
INDASTRO
Profskrin RC45-1.25 — thixotropic R4 mortar with fine 1.25 mm aggregate
Thixotropic R4 mortar with 1.25 mm aggregate for structural repair of concrete; 20 MPa in 24 hours and 45 MPa in 28 days.
Price on request
INDASTRO
Profskrin RC45-1.25 F — winter fine-grained thixotropic R4 mortar
Winter thixotropic R4 mortar with 1.25 mm aggregate for repairing concrete structures at temperatures from −10 to +10 °C.
Price on request
INDASTRO
Profskrin RC470 — R4 repair mortar for structures of class B50 and above
Thixotropic R4 mortar for repairing high-strength concrete and reinforced concrete of B50 and above; 70 MPa at 28 days, water impermeability W20.
Price on request
INDASTRO
Profskrin RC50 RTi — ultra-rapid-hardening thixotropic R4 mortar with fibre
Non-shrink thixotropic R4 mortar to EN 1504 with polymer fibre: 20 MPa in compression after 2 hours, work at temperatures from −10 to +35 °C.
Price on request
INDASTRO
Profskrin RC60 — thixotropic R4 mortar for repairing high-strength concrete, 60 MPa
Thixotropic R4 repair mortar for high-strength concrete structures; at least 30 MPa after 24 hours and from 60 MPa after 28 days.
Price on request
INDASTRO
Profskrin RC60 F — winter R4 mortar for high-strength concrete at −10…+10 °C
Thixotropic R4 mortar for repairing high-strength concrete structures in winter, at temperatures from −10 to +10 °C; 60 MPa in compression at 28 days.
Price on request
INDASTRO
Profskrin RC80 — thixotropic R4 mortar for concrete of class B60 and above
Thixotropic R4 repair mortar for structures made of B60 concrete and above; compressive strength at 28 days at least 80 MPa, flexural strength 10 MPa.
Price on request
REKS
REKS® AR — thixotropic R4 repair mortar for spraying and trowel application
Non-shrink fibre-reinforced R4 mortar in 25 kg bags for repairing bridges, tunnels, dams and columns; compressive strength from 55 MPa at 28 days.
Price on request
REKS
REKS® AR FM — R4 repair mortar for wet spraying, supplied with fibre
Thixotropic class R4 mortar for repairing bridges, tunnels and columns by spraying or trowel; each bag comes with a pail of fibre, flexure from 12 MPa.
Price on request
REKS
REKS® BS — thixotropic R3 mortar for final levelling of concrete
Non-shrink class R3 mortar for a smooth finish on new and repair of old concrete surfaces before protective coatings; aggregate size 0.315 mm.
Price on request
REKS
REKS® OL — lightweight thixotropic R3 mortar for repairing soffits
Non-shrink lightweight cementitious R3 mortar for overhead surfaces and extensive concrete damage; density of the hardened mortar 1.5 t/m³.
Price on request
REKS
REKS® R3 — class R3 repair mortar, 40 MPa, for interior and exterior work
Non-shrink thixotropic class R3 mortar for local repair and levelling of reinforced concrete in industrial buildings and tanks; compression from 40 MPa.
Price on request
REKS
REKS® R4 — mortar for structural repair of reinforced concrete, 60 MPa
Fibre-reinforced thixotropic class R4 mortar for structural repair of reinforced concrete on vertical, horizontal and overhead surfaces.
Price on request
REKS
REKS® Strukto 100 — thixotropic R4 repair mortar resistant to acidic media
Non-shrink fibre-reinforced R4 mortar for bridges, tunnels, dams and treatment plants, tested for resistance in liquid acidic aggressive media.
Price on request
REKS
REKS® Strukto 300 — rapid-setting R4 mortar for repair and joint filling
Thixotropic class R4 cementitious mortar for fast concrete repair and joint filling in industrial buildings and tunnels; from 30 MPa after one day.
Price on request
REKS
REKS® Strukto 60 — fibre-reinforced thixotropic R4 repair mortar, 60 MPa
Non-shrink fibre-reinforced R4 mortar for repairing bridges, tunnels, dams and columns; compressive strength at 28 days at least 60 MPa.
Price on request
REKS
REKS® Strukto 70 — thixotropic R4 repair mortar, 70 MPa, W20
Fibre-reinforced R4 repair mortar for bridges, dams, tunnels and columns with compressive strength from 70 MPa and water impermeability W20.
Price on request
REKS
REKS® Strukto BS 3 — rapid-hardening thixotropic R4 mortar for work down to −10 °C
Rapid-setting fibre-reinforced R4 mortar for repairing walls and soffits without formwork, including in frost; from 20 MPa compression after 2 hours.
Price on request
REKS
REKS® Strukto R3 — rapid-setting class R3 mortar for repair and levelling
Non-shrink fibre-reinforced R3 mortar for repair, finishing and local levelling of concrete, including precast elements; 35 MPa at 28 days.
Price on request
REKS
REKS® Strukto R4 — rapid-setting fibre-reinforced repair mortar of class R4
Rapid-setting mortar for repairing concrete after rebar corrosion and impact, resistant to liquid acidic media; from 30 MPa compression after one day.
Price on request
REKS
REKS® Tikso — thixotropic mortar for repairing and levelling concrete and floors
Fibre-reinforced non-shrink mortar for repair, finishing and local levelling of concrete, including floors; flowability is retained from 60 minutes.
Price on request
Vetonit
Vetonit remokor N-35 — fine-grained thixotropic mortar, class R3
Fine-grained thixotropic class R3 mix for finishing repair of reinforced concrete and for eliminating pores and cavities on walls and ceilings; W8.
Price on request
Vetonit
Vetonit remokor N-40 — thixotropic levelling mortar, class R3
Fine-grained thixotropic class R3 mix for levelling, finishing and protecting reinforced concrete against aggressive media; 40 MPa compressive, W12.
Price on request
Vetonit
Vetonit remokor NS-40 — fast class R3 finishing mortar for work in frost
Rapid-hardening fine-grained class R3 mix for urgent repair and finishing of reinforced concrete on walls and ceilings at temperatures down to −10 °C.
Price on request
Vetonit
Vetonit remokor T-45 — thixotropic class R4 mortar on cement with polymers
Fine-grained thixotropic class R4 mix with increased crack resistance for repairing reinforced concrete on walls and ceilings.
Price on request
Vetonit
Vetonit remokor T-60 — high-strength thixotropic mortar, class R4
Thixotropic non-shrink class R4 mix for repairing beams, bridge slabs, pylons and piers by hand or by spraying; 60 MPa compressive.
Price on request
Vetonit
Vetonit remokor TF-60 — thixotropic class R4 mortar with metal fibre
Thixotropic class R4 mix with polymer and metal fibre for columns, arches, bridge slabs and dams under impact loads; flexural strength 10 MPa.
Price on request
Vetonit
Vetonit remokor TS-60 — rapid-hardening thixotropic R4 mortar down to −10 °C
Rapid-hardening thixotropic class R4 mix for repairing hydraulic structures, bridges, roads and airfields without heating in frost down to −10 °C.
Price on request
CarbonWrap
CarbonWrap® Repair FS repair mortar — rapid-hardening non-shrink mix
Non-shrink rapid-hardening mix for fast repair of concrete, masonry and cellular concrete, including under CarbonWrap Grid; 30 MPa after one day.
Price on request
CarbonWrap
CarbonWrap® Repair ST repair mortar — thixotropic mix with fibre
Thixotropic fibre-reinforced cement mix for restoring spalls, potholes and cracks in concrete, including under CarbonWrap Grid.
Price on request
No materials match these filters.